Results 145 - 192 of 198 - RT809H EMMC-Nand FLASH Programmer +26 Adapters. Newest CARPROG V10.93 Carprog V10.0.5 V8.21 Car Prog ECU Chip-Car.

Operating System Android Processor Quad-core 1.60GHz Processor Memory 1G RAM,16G FLASH Display 9.7 inch capacitive touch screen with 1024×768P resolution Camera Rear camera, 5.0 Megapixel, AF with Flashlight. Sensors Gravity Sensor Audio Input/Output Microphone, Dual Speakers, 4-Band 3.5 mm stereo/standard headset jack Power and Battery 16000mAh, 3.7V lithium-polymer battery Power Voltage 8V Operating Temperature -20 to 50℃(-4 to 12℉) Humidity. About product and suppliers: Alibaba.com offers 447 immo programmer products. About 88% of these are diagnostic tools, 1% are integrated circuits, and 1% are locksmith supplies. A wide variety of immo programmer options are available to you, such as code reader, engine analyzer, and voltage regulator.

You can also choose from paid samples, free samples. There are 447 immo programmer suppliers, mainly located in Asia. The top supplying country is China (Mainland), which supply 100% of immo programmer respectively. Immo programmer products are most popular in North America, South America, and Africa. You can ensure product safety by selecting from certified suppliers, including 8 with Other, 3 with ISO9001, and 2 with ISO13485 certification.

(, 07:09 AM)Willail Wrote: (, 12:23 PM)dil6222 Wrote: (, 11:15 AM)Willail Wrote: (, 05:00 AM)23Andi23 Wrote: (, 04:51 AM)Willail Wrote: Hello, change the 4 IC 74HC125D is the only modification to rework carprog 7.28? Thanks for your help What not work? Antenna is working? Can bus is working? Hello, i have a clone carprog using solfware 7.28.

Since i received it, it is impossible to read eeproms 95160 and 24cxx. I so used the software with airbag, but the ID of the Eproom is not recognised. The eprooms were desolder from the pcb and i used the A4 and A5 adapters provided with carprog.

I have verified that the wires were correct with a multimeter (continuity test). I don't know if the changes of the 4 IC will help to read eprooms. I very dissapointed I don't test if antenna and CAN bus are working?

How do i make it? Thanks for your reply (, 10:47 AM)23Andi23 Wrote: (, 10:00 AM)Willail Wrote: Hello, Do you have already reworked clone carprog V7.28? Rukovodstvo po remontu i ekspluatacii avtobusa yutong 6737d. Thanks Hello, What's a good pcb of carprog? COuld you send me a picture?

Yhanks Look one Page back post nr. 780 in this thread Most people flash to 8.21 and make rework like on many pictures in this thread Hello, thank you for this reply. I will send you some picture of my carprog. Then, you will tell me if it is a good pcb. Can you give the main changes to make at the rear of the pcb because on the pictures, it is not easy to understand (remove some capacitors, remplace by a what? Repair the hole line missing? Thanks (, 06:27 AM)kastanka Wrote: (, 17:27 PM)dil6222 Wrote: That's 1 of a few mods you can do you can try this but I haven't tested it.

I tested it and work perfect. Hello, could you explain me the changes that you made on your carprog for held reading and writing eprooms? Kubota ask r150 manual. Add a 120 ohm resistor and change the 4 iC 74HC125D by 74HCT125M?

Here we go this is good start and yes change 4x 74HC125D to 74HC125M i will post some pictures of the other mods shortly hope this helps don't forget to thanks and rep those who have helped you Hello, thank for your reply. Do you know where i can buy some good 74HCT125M? It is possible to buy on Ebay?

Some friends say that the components on Ebay are not original and are bad. Thanksi not change 4x 74HC125D to 74HC125M and well read-write 24cxx,95x without any problem. (, 09:40 AM)kastanka Wrote: (, 07:09 AM)Willail Wrote: (, 12:23 PM)dil6222 Wrote: (, 11:15 AM)Willail Wrote: (, 05:00 AM)23Andi23 Wrote: What not work? Antenna is working? Can bus is working?

Hello, i have a clone carprog using solfware 7.28. Since i received it, it is impossible to read eeproms 95160 and 24cxx. I so used the software with airbag, but the ID of the Eproom is not recognised. The eprooms were desolder from the pcb and i used the A4 and A5 adapters provided with carprog.

I have verified that the wires were correct with a multimeter (continuity test). I don't know if the changes of the 4 IC will help to read eprooms. I very dissapointed I don't test if antenna and CAN bus are working? How do i make it?